Well got up to practice.

 

We have two U-shaped core of ferrite grade 2500NM. Unfortunately, the capabilities of my computer does not allow us to make a decent graphics, no scanner and digital camera too, so try to describe clearly, well, reading a little stretch their imagination.

 

These cores are placed close to each end face of the other to get what is represented in the photograph. The truth is another product and it's not iron, and a core of amorphous metal, the more "zabugornye. And the parameters of his ideal for our problem, but us only dream of such a material has, therefore, focus not on what you need, and the fact that you can buy at "Mitka".

  So I have a similar thing obtained only from iron.

 

Then - in the middle put a permanent magnet on the seam. North-up, down-south. I hope it is clear. What happens in this case - correctly, the magnetic flux from the permanent magnet is distributed on both shoulders of the core equally.

 

Further, the upper horizontal section of the wound two small coils, located on both sides of the magnet. In this case, the coil, when power to create its own magnetic flux is directed opposite to the flow of a permanent magnet in his shoulder.

 

Now the fun begins.

 Will submit a current pulse to one of the coils.

  Its magnetic flux is directed against the magnetic flux permanent magnet, as a result of the magnetic lines of the magnet Redistribute (because they may not destroy or disperse) and go into the second arm of the magnetic circuit, the path of least resistance. Accordingly, in the second arm is changing magnetic flux. A changing magnetic flux that occurs - induced emf. And that would remove this EMF on the vertical side cores we reels reel, on which the induced emf is induced. I hope no one argue with that will not happen. On the magnetic flux we spend energy. How much - this is a separate issue to be clarified in future experiments. Previously (based on results of the experiments), I can say that this energy is expended in less than an induced emf. After all, we redistribute only part of the magnetic flux from the permanent magnet, and EDS brings the total magnetic flux. Feel a chip? Quantitatively, this time clarifying further setup.

 

And now attention - the most interesting. We take - and just turn off the little control coils. Magnetic lines of the magnet again redistributed and evenly divided between first and second shoulder magnetic core. What happens here, because the magnetic flux has changed - again induced emf. Spent 0 (exactly ZERO) W of energy and got the induced EMF. Here and firewood, can ignite.

 

We are not just a transformer, a system with a permanent magnet. I explain. Number of magnetic lines of magnetic changes in the shoulder? Of course. We're spending power to support the transition process? Naturally. But not in the military option, when all our power usage goes to the magnetic flux on a good level "

 to maintain the induction, but only on the redistribution of magnetic field lines. Especially I specify - we are not reversing the magnet. He lies in peace in the middle, and we redistribute the branches of its magnetic flux.

In other words, we have a swing that is very easy to shake. And accordingly, the force function is vested in the magnet itself, since it supports a certain level of magnetic induction interaction on any number of turns of secondary housing. The greater the frequency of the "swing" of the magnetic field, the more power generated.

 

Hence it is very good value for spent / received energy.

Of course, there are boundary conditions, as in every system. They are known for, so focus attention on them does not make sense.

 

Everything is simple and clear - take it and shake energy. But it is only in general terms. But there are little things, without which this process is not efficient, but simply zero. And what is this stuff?

 

Every natural system is harmonious. According to another and can not be, because in nature (as opposed to people with their delusional laws, committees, candy wrappers, etc.) all are in harmony. And how this harmony is achieved? Let us recall the concepts such as dissonas and resonance. So that's what it is - to build a harmonious processes and systems. Not for energy (this is a dead end) and to harmonize the process of obtaining ENERGY. Here we come to defining the location

 resonance in this process. And this is not a resonance LC-circuit in which all long and unsuccessfully looking for energy (ie, looking for where the light, but not where applicable). A response system and combination resonances of each element of the system. And by the way, absolutely not

  necessary that these elements would operate on one frequency. I will say more, in this case, the system will not be harmonious, and nothing will give. Look around, and everything will become clear.

 

Something else is missing? Still need something - Time!

 

And what is time - is the frequency response of the energy of the filling medium. And where is the frequency, there's a resonance. The chain is closed. Ie in the system, each element can be operated at its resonant frequency and connects their work (more precisely, the results of) these elements are time. Everything must be coordinated in time and the time of each element, then the system will be harmonious.

 

 Control coils consume energy as much as is necessary to switch the flow, and do it accurately and on time and in harmony with the work of detachable coils and other elements of the system. Hence the result.

 

 And this is not the only scheme to obtain energy. In the process of mining parameters and elements vyrisovalsya a number of designs that are waiting for their turn.

 

A formula, the calculations?

Will be calculated and the formula. The main thing to understand what should be considered.

 

As one example, I can say that on an oscilloscope, we see not the process itself, as a consequence of this process. How to verify that this is so - elementary, fill the bath water, take a small narrow board and start to shake it in water. Obtained wave. Please note that the frequency of these waves will differ from the frequencies of plaques. And the higher the frequency, the greater the difference. So on an oscilloscope, we see no reason, "vibration plates" as a consequence - the waves on the water. Ie we look not the process itself, and the reaction medium on the process. And the process itself is quite a different frequency range. And what to base the calculations? Now take effect.

 

In general, modern physics - the physics effects, but must seek the causes and their relationships.

Therefore, the formulas do not need to hurry, but it is possible to count.

Formula will be - in the sequel. But at this point, I said enough.